Vagcom 409.1 USB KKL OBD2 Diagnostic Cable VAG-COM Vag 409 support Dual K-Lines

VAGCOM 409.1 Diagnostic Cable Highlights:
 
1. Support langauge: English Only
 
2. Support most VAG car models from year 1996-2009
 
3. Operating Software Compatibility: Windows XP Only
 
4. Save on expensive garage fees by diagnosing your car’s faults.
 
 
Notice:
 
 
1. If the CD you get is broken, it maybe get damaged in transit. Please do not worry about it, we would send you the software download link by Email which you can download it directly.
 
2. Not support  Caddy (2K) / Golf MK5 (1K) / Golf Plus / Jetta MK5 (1K) / Passat MK5 (B6) / Passat MK6 (B6) / Phaeton /Touran (1T)
 
3. If you want to buy  Vag409.1 With FTDI FT232 FT232RL Chip , please check there:  Model: EBD019 http://www.obd2cartool.com/vag-kkl-fiat-ecu-scan-work-on-windows-xp-win7-p-139
 
 
VAGCOM 409.1 Diagnostic Cable Description:
 
1. This VAG COM 409.1 OBD II interface enables you to connect your PC to your car so that you can troubleshoot any problems in your vehicle by reading the Diagnostic Trouble Codes (DTC’s) that appear when the ‘check engine’ light is showing.
 
2. This adapter is fully compatible with the diagnostic software version 409.1 from VAG-COM – a software programme that turns your PC into a sophisticated diagnostic tool.

VAGCOM 409.1 Diagnostic Cable Function:
 
1.This cable can not work if your car uses a protocol/ bussystem like VPW,PWM or Can-bus.
2.Terminal Bus of communication
3.Terminal L= Ignition for waking up car computing system (ECU: Engine Control Unit)
4. Existed 3 different protocols with same OBD2 connector incl. ISO/KWP, VPW, PMW
5.This K/L Diaqnostic interface & cables work on ISO/KWP (Kev Word Protocol) Iaunched after 1996 only
6. Supported also ISO9141 protocol
7. The cables may work with some versions of the Carsoft, but carsoft used a lot of different intercaces during the different versions and also had some custom interfaces.
8. Product running as virtual comport, like many products it usees a USB to Rs232 converter chip .But under special circumstances this can give some problems regarding time especially on the handshake lines.
9. Read & erase error code, log data e. g. speed, gasoline, consume engine-rotating(RPM: Rotation Per Minutes).
 
 
VAGCOM 409.1 Diagnostic Cable Features:
 
1. Supports VAG-COM version 409.1 or older.
2. Fully automatic support for 2002 with dual K-lines.
3. High quality precision moulded diagnostic connector made to fit all .
4. LED light shows cable communication status.
5. Fully CE approved
6. In-built electronic protection from aftermarket radio problems
7. Fully compatible with all models of the above casr or van produced between 1996 and 2004.
8. Compatible with the above cars with CAN connection.
9. Has a data base of more than 7500 fault codes and measuring block texts.
10. Can use the new 7 PIN/SKC codes to match new keys in all immobilizer
 
 
VAGCOM 409.1 Diagnostic Cable Specifications:
 
1. Car side: OBDII standard plug
2. PC side: USB interface
3. Circuit insulation sealed: waterproof, anti-static, harsh environments
4. Color: Blue

USB Driver Installation Tips:
 
(For all Ross-Tech USB interfaces with VAG-COM Release 504.1 or newer) KKL+CAN BUS USB CABLE..
 
Notes: These instructions are for Windows XP (which we highly recommend with our USB Interfaces). Installation under Windows 98/ME/2000 is similar, but not necessarily identical.  
 
1. Make sure you have already downloaded and installed VAG-COM on your PC before following these instructions. If you haven't yet downloaded VAG-COM, then use this website to open our download page in a new window.     website
 
2. Allow the software you just downloaded to install itself on your PC. If you choose to install it someplace other than the default location, make a note of folder you're installing it to.
 
3. Plug your Ross-Tech USB Interface to your PC's USB port. (It is not necessary to connect the interface to a car yet)

4. On the screen above, select "Install from a list or specific location (Advanced)" then click the [Next >] button.  

5. On the screen above:
Select "Search for the best driver in these locations"
Check "Include this location in the search:"
Use the [Browse] button to find the VAG-COM folder
(Usually C:Program FilesVag-Com, unless you chose a different folder when you installed the software)
Click [OK]

6. Click the [Next >] button.

7. This dialog warns you that we haven't paid Microsoft a pound of flesh to certify the driver. You're going to have to click the [Continue Anyway] button..:-)

8. Click the [Finish] button to complete the installation.
9. Start VAG-COM.
Click the [Options] button.
In the "Select COM Port" box, select USB.
Click the [Test] button.
The results should look like this (it may have additional information in the Port Test dialog).

10. Click [OK] and click [Save]
11. Go test it on a car.  :-)
NOTE: If the new Hardware Found Wizard does not appear when you plug in your interface, go to Device Manager and look for the interface. It should be under Universal Serial Bus (USB) Controllers or under Other Devices. If it's there, Right-Click it and then select Update Driver.Then you can start at Step 4 in the instructions above.

Packing list:

1pc* VAG 409.1 USB cable
1pc* Driver CD